Environmental test EN 60068-2-14.
| Open loop voltage | 20 V |
| Relative humidity | 95 % non-condensing |
| Damaging gas | Operation in environmental conditions according to ISA-S71.04-1985, severity level G3. |
| Degree of protection | IEC 60529 |
| Electromagnetic compatibility | NE 21 |
| Interface | Manufacturer-specific bus to standard communication unit. |
| Vibration resistance | Frequency range 10 … 150 Hz; transition frequency: 57.56 Hz, amplitude/acceleration ?± 0.075 mm/1 g; 10 cycles. Frequency range 5 … 100 Hz; transition frequency: 13.2 Hz amplitude/acceleration ?± 1 mm/0.7 g; 90 minutes at each resonance. |
| Vibration resistance | EN 60068-2-6 |
| Rated voltage | 12 V DC (only in connection with power supplies LB9***). |
| Certificate | PF 08 CERT 1234 X. |
| Watchdog | Device enters safe state within 0.5 s, e.g., after loss of communication. |
| Number of channels | 8. |
| Connection | Channel I: 1+, 2-; Channel II: 3+, 4-; Channel III: 5+, 6-; Channel IV: 7+, 8-; Channel V: 9+, 10-; Channel VI: 11+, 12-; Channel VII: 13+, 14-; Channel VIII: 15+, 16-. |
| EU-Type Examination Certificate | PTB 03 ATEX 2042. |
| EAC approval | Russia: RU C-IT.MIII06.B.00129. |
| Coding | Optional mechanical coding via front socket. |
| Relative humidity | EN 60068-2-56 |
| Response time | 20 ms (depending on bus cycle time). |
| Supplementary information | EC-Type Examination Certificate, Statement of Conformity, Declaration of Conformity, Attestation of Conformity and instructions must be observed where applicable. See www.pepperl-fuchs.com for details. |
| Connection | Backplane bus. |
| Degree of protection | IP20 when mounted on backplane. |
| Dimensions | 32.5 x 100 x 102 mm (1.28 x 3.9 x 4 inch). |
| Power consumption | 2.35 W. |
| ATEX approval | PF 08 CERT 1234 X PTB 03 ATEX 2042. |
| System information | The module must be mounted in appropriate backplanes (LB9***) in Zone 2 or outside hazardous areas. Observe the corresponding declaration of conformity. For use in hazardous areas (e.g., Zone 2, Zone 22, or Div. 2), the module must be installed in an appropriate enclosure. |
| Shock resistance | Shock type I, shock duration 11 ms, shock amplitude 15 g, number of shocks 18. |
| Ambient temperature | -20 … 60 °C (-4 … 140 °F). |
| Power dissipation | 2.35 W. |
| Damaging gas | EN 60068-2-42. |
| Shock resistance | EN 60068-2-27. |
| Storage temperature | -25 … 85 °C (-13 … 185 °F). |
| Connection | Removable front connector with screw flange (accessory). Wiring connection via spring terminals (0.14 … 1.5 mm²) or screw terminals (0.08 … 1.5 mm²). |
| Line fault detection | Can be switched on/off for each channel via configuration tool. |
| LED indication | LED green: supply. LED red: line fault, communication error (flashing). |
| Current limit | 8 mA. |
| Mass | Approx. 160 g. |
| IECEx approval | BVS 09.0037X. |
| Occupied slots | 2. |
| Connection | Backplane bus. |
